User Contributed                                            MET/CAL Procedure
=============================================================================
INSTRUMENT:            OSP-4L Acceleration Sub
DATE:                  17-Sep-97
AUTHOR:                User Contributed
REVISION:
ADJUSTMENT THRESHOLD:  70%
NUMBER OF TESTS:       17
NUMBER OF LINES:       141
CONFIGURATION:         HP 34401A
=============================================================================
 STEP    FSC    RANGE NOMINAL        TOLERANCE     MOD1        MOD2  3  4 CON
  1.001  HEAD         { Acceleration/Vibration Meter }
  1.002  HEAD         { Channel 1  }
  1.003  JMP          2.001
  1.004  EVAL
  2.001  DISP         On the rear of the UUT use a tee connector to
  2.001  DISP         connect the COMP OUT to the 10mV/g IN and to the DMM.
  2.002  DISP         Make sure the rear panel selector switch is in the
  2.002  DISP         proper position for 10mV/g inputs.
  2.003  DISP         Set the UUT as follows:
  2.003  DISP         MAX OUT ....................... Full cw
  2.003  DISP         MAX SPEED ..................... 3k dB/sec
  2.003  DISP         ACC/DISP buttons .............. ACC (all)
  2.003  DISP         LEVEL MULTIPLIERS ............. X10, F.S. 10 (all)
  2.003  DISP         LEVEL VERNIER ................. 10.00 (10 turns, all)
  2.003  DISP         SERVO MODE .................... ON
  2.004  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
  2.005  DISP         If necessary adjust the crossover controls
  2.005  DISP         so that channel 1 is active.  To change the active
  2.005  DISP         channel, adjust the control in the direction of
  2.005  DISP         the currently active channel until the active LED
  2.005  DISP         changes to the adjacent channel.  Continue this process
  2.005  DISP         until channel 1 is active.
  2.006  DISP         Adjust the COARSE and FINE controls for an
  2.006  DISP         output of 100Hz.
  2.007  IEEE         [@34401]READ?[I][GTL]
  2.008  ACC    0.1   70.700mV       0.06P% 0.04/
  2.009  MEM*         1000
  2.010  MEME
  2.011  MEMC         mV             1.000%
#!          Test Tol 0.707, Sys Tol 4.4242e-005, TUR 15980.290 (>= 4.00).
  3.001  MEMI         Enter the UUT ACC meter reading in g-pk.
  3.002  ASK-                              U
  3.003  MATH         mem1= 10
  3.004  MEME
  3.005  MEMC         gpk            1.00%
#! T.U.R. not calculated because ASK 'U' is not set.
  4.001  ASK+                              U
  4.002  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
  4.003  DISP         Adjust the LEVEL VERNIER to 1.00 (1.0 turns).
  4.004  IEEE         [@34401]READ?[I][GTL]
  4.005  ACC    0.1   7.070mV        0.06P% 0.04/
  4.006  MEM*         1000
  4.007  MEME
  4.008  MEMC         mV             1.000%
#!          Test Tol 0.0707, Sys Tol 4.0424e-005, TUR 1748.952 (>= 4.00).
  5.001  HEAD         {  Channel 2  }
  5.002  JMP          6.001
  5.003  EVAL
  6.001  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
  6.002  DISP         Adjust the CROSSOVER for channel 2 operation.
  6.003  IEEE         [@34401]READ?[I][GTL]
  6.004  ACC    0.1   70.700mV       0.06P% 0.04/
  6.005  MEM*         1000
  6.006  MEME
  6.007  MEMC         mV             1.000%
#!          Test Tol 0.707, Sys Tol 4.4242e-005, TUR 15980.290 (>= 4.00).
  7.001  MEMI         Enter the UUT ACC meter reading in g-pk.
  7.002  ASK-                              U
  7.003  MATH         mem1= 10
  7.004  MEME
  7.005  MEMC         gpk            1.00%
#! T.U.R. not calculated because ASK 'U' is not set.
  8.001  ASK+                              U
  8.002  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
  8.003  DISP         Adjust the LEVEL VERNIER to 1.00 (1.0 turns).
  8.004  IEEE         [@34401]READ?[I][GTL]
  8.005  ACC    0.1   7.070mV        0.06P% 0.04/
  8.006  MEM*         1000
  8.007  MEME
  8.008  MEMC         mV             1.000%
#!          Test Tol 0.0707, Sys Tol 4.0424e-005, TUR 1748.952 (>= 4.00).
  9.001  HEAD         {  Channel 3  }
  9.002  JMP          10.001
  9.003  EVAL
 10.001  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
 10.002  DISP         Adjust the CROSSOVER for channel 3 operation.
 10.003  IEEE         [@34401]READ?[I][GTL]
 10.004  ACC    0.1   70.700mV       0.06P% 0.04/
 10.005  MEM*         1000
 10.006  MEME
 10.007  MEMC         mV             1.000%
#!          Test Tol 0.707, Sys Tol 4.4242e-005, TUR 15980.290 (>= 4.00).
 11.001  MEMI         Enter the UUT ACC meter reading in g-pk.
 11.002  ASK-                              U
 11.003  MATH         mem1= 10
 11.004  MEME
 11.005  MEMC         gpk            1.00%
#! T.U.R. not calculated because ASK 'U' is not set.
 12.001  ASK+                              U
 12.002  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
 12.003  DISP         Adjust the LEVEL VERNIER to 1.00 (1.0 turns).
 12.004  IEEE         [@34401]READ?[I][GTL]
 12.005  ACC    0.1   7.070mV        0.06P% 0.04/
 12.006  MEM*         1000
 12.007  MEME
 12.008  MEMC         mV             1.000%
#!          Test Tol 0.0707, Sys Tol 4.0424e-005, TUR 1748.952 (>= 4.00).
 13.001  HEAD         {  Channel 4  }
 13.002  JMP          14.001
 13.003  EVAL
 14.001  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
 14.002  DISP         Adjust the CROSSOVER for channel 4 operation.
 14.003  IEEE         [@34401]READ?[I][GTL]
 14.004  ACC    0.1   70.700mV       0.06P% 0.04/
 14.005  MEM*         1000
 14.006  MEME
 14.007  MEMC         mV             1.000%
#!          Test Tol 0.707, Sys Tol 4.4242e-005, TUR 15980.290 (>= 4.00).
 15.001  MEMI         Enter the UUT ACC meter reading in g-pk.
 15.002  ASK-                              U
 15.003  MATH         mem1= 10
 15.004  MEME
 15.005  MEMC         gpk            1.00%
#! T.U.R. not calculated because ASK 'U' is not set.
 16.001  ASK+                              U
 16.002  IEEE         [@34401]FUNC "VOLT:AC"[GTL]
 16.003  DISP         Adjust the LEVEL VERNIER to 1.00 (1.0 turns).
 16.004  IEEE         [@34401]READ?[I][GTL]
 16.005  ACC    0.1   7.070mV        0.06P% 0.04/
 16.006  MEM*         1000
 16.007  MEME
 16.008  MEMC         mV             1.000%
#!          Test Tol 0.0707, Sys Tol 4.0424e-005, TUR 1748.952 (>= 4.00).
 17.001  END
#! T.U.R.s less than 4.00:                  0
#! T.U.R.s estimated using RANGE value:     0
#! T.U.R.s not calculated (ASK- U):         4
#! T.U.R.s not computable at compile time:  0
#! FOR JUSTIFICATION REFER TO COMMENTS FOLLOWING EACH TEST IN THIS LISTING.